• Low-velocity impact of composite laminates: damage evolution

      Shi, Yu; Pinna, Christophe; Soutis, Constantinos; University of Chester; University of Sheffield; University of Manchester (Woodhead Publishing, 2016-02-19)
      This chapter presents modelling procedures used to simulate damage evolution in composite laminates used in aircraft structures when subjected to low-energy-level impact (≤15 J). Damage models for both initiation and evolution are first introduced by considering the individual damage modes of composite laminates in the form of intra- and inter-laminar damage mechanisms. The implementation of these damage criteria into the user subroutine Vumat of the finite element code Abaqus is then described for the simulation of damage development during low-velocity impact tests. Finite element prediction is then compared to experimental load-time measurements and damage extent obtained using X-rays as a non-destructive technique (NDT). Further development of the model is then presented by simulating matrix cracking evolution and splitting using a fracture mechanics-based criterion approach implemented into a cohesive zone element (CZE) formulation. Results from the extended model show clear improvement in terms of the accuracy of damage prediction, with experimental observations of the damage modes operating at ply-level providing further validation of the model. This can be used at an early stage of the design process of optimising laminate configurations used in aircraft structural applications.
    • Eight parametric resonances in a multi-frequency wideband MEMS piezoelectric vibration energy harvester

      Jia, Yu; Du, Sijun; Seshia, Ashwin A.; University of Cambridge; University of Chester (IEEE, 2016-01-24)
      This paper presents a multi-order parametric resonant MEMS piezoelectric disk membrane, for the purpose of broadening the operational frequency bandwidth of a vibration energy harvester by employing the nonlinearity-induced bandwidth broadening associated with this phenomenon as well as the multi-frequency response associated with the higher orders. The fundamental mode -3dB bandwidth at 2.0 g recorded 55 Hz, while the first parametric resonant peak exhibited 365 Hz and the -3dB of the first 8 orders accumulated to 604 Hz. The membrane parametric resonator also experimentally demonstrated over 3-folds improvement in power density compared to a conventional direct resonator (cantilever), when subjected to band-limited white noise.
    • On the study of oil paint adhesion on optically transparent glass: Conservation of reverse paintings on glass

      Bayle, M.; Waugh, David G.; Colston, Belinda J.; Lawrence, Jonathan; University of Chester (Elsevier, 2015-12-01)
      Reverse painting on glass is a technique which consists of applying a cold paint layer on the reverse-side of glass. The main challenge facing these artworks is the fragile adhesion of the pictorial layer – a simple movement can modify the appearance of the painting. This paper details a study into the adhesion parameters of pigments on glass and the comparison between different pigments. The relationships between the binder (linseed oil) with pigments and the glass with or without the use of an adhesive are studied. Physical analyses by surface characterisation have been carried out to better understand the influence of the pigment. The use of a sessile drop device, optical microscopy, scanning electron microscopy (SEM), a surface 3D profiler and a pencil hardness scratch tester were necessary to establish a comparison of the pictorial layer adhesion. A comparison of the effect of two adhesives; namely ox gall and gum arabic, has shown that the adhesion is not only linked to the physical parameters but that possible chemical reactions can influence the results. Finally, a treatment based on humidity-extreme storage has shown the weakness of some pictorial layers.
    • Cantilevers-on-membrane design for broadband MEMS piezoelectric vibration energy harvesting

      Jia, Yu; Du, Sijun; Seshia, Ashwin A.; University of Chester; University of Cambridge (IOP Publishing, 2015-12-01)
      Most MEMS piezoelectric vibration energy harvesters involve either cantilever-based topologies, doubly-clamped beams or membrane structures. While these traditional designs offer simplicity, their frequency response for broadband excitation are typically inadequate. This paper presents a new integrated cantilever-on-membrane design that attempts to both optimise the strain distribution on a piezoelectric membrane resonator and improve the power responsiveness of the harvester for broadband excitation. While a classic membrane-based resonator has the potential to theoretically offer wider operational frequency bandwidth than its cantilever counterpart, the addition of a centred proof mass neutralises its otherwise high strain energy regions. The proposed topology addresses this issue by relocating the proof mass onto subsidiary cantilevers and integrates the merits of both the membrane and the cantilever designs. When experimentally subjected to a band-limited white noise excitation, up to approximately two folds of power enhancement was observed for the new membrane harvester compared to a classic plain membrane device.
    • Maximizing Output Power in a Cantilevered Piezoelectric Vibration Energy Harvester by Electrode Design

      Du, Sijun; Jia, Yu; Seshia, Ashwin A.; University of Cambridge; University of Chester (IOP Publishing, 2015-12-01)
      A resonant vibration energy harvester typically comprises of a clamped anchor and a vibrating shuttle with a proof mass. Piezoelectric materials are embedded in locations of high strain in order to transduce mechanical deformation into electric charge. Conventional design for piezoelectric vibration energy harvesters (PVEH) usually utilizes piezoelectric material and metal electrode layers covering the entire surface area of the cantilever with no consideration provided to examining the trade-off involved with respect to maximizing output power. This paper reports on the theory and experimental verification underpinning optimization of the active electrode area of a cantilevered PVEH in order to maximize output power. The analytical formulation utilizes Euler-Bernoulli beam theory to model the mechanical response of the cantilever. The expression for output power is reduced to a fifth order polynomial expression as a function of the electrode area. The maximum output power corresponds to the case when 44% area of the cantilever is covered by electrode metal. Experimental results are also provided to verify the theory.
    • A vibration powered wireless mote on the Forth Road Bridge

      Jia, Yu; Yan, Jize; Feng, Tao; Du, Sijun; Fidler, Paul; Soga, Kenichi; Middleton, Campbell; Seshia, Ashwin A.; University of Chester; University of Cambridge (IOP Publishing, 2015-12-01)
      The conventional resonant-approaches to scavenge kinetic energy are typically confined to narrow and single-band frequencies. The vibration energy harvester device reported here combines both direct resonance and parametric resonance in order to enhance the power responsiveness towards more efficient harnessing of real-world ambient vibration. A packaged electromagnetic harvester designed to operate in both of these resonant regimes was tested in situ on the Forth Road Bridge. In the field-site, the harvester, with an operational volume of ~126 cm3, was capable of recovering in excess of 1 mW average raw AC power from the traffic-induced vibrations in the lateral bracing structures underneath the bridge deck. The harvester was integrated off-board with a power conditioning circuit and a wireless mote. Duty- cycled wireless transmissions from the vibration-powered mote was successfully sustained by the recovered ambient energy. This limited duration field test provides the initial validation for realising vibration-powered wireless structural health monitoring systems in real world infrastructure, where the vibration profile is both broadband and intermittent.
    • Modelling transverse matrix cracking and splitting of cross-ply composite laminates under four point bending

      Shi, Yu; Soutis, Constantinos; University of Chester; University of Manchester (Elsevier, 2015-11-30)
      The transverse matrix cracking and splitting in a cross-ply composite laminate has been modelled using the finite element (FE) method with the commercial code Abaqus/Explicit 6.10. The equivalent constraint model (ECM) developed by Soutis et al. has been used for the theoretical prediction of matrix cracking and results have been compared to those obtained experimentally and numerically. A stress-based traction–separation law has been used to simulate the initiation of matrix cracks and their growth under mixed-mode loading. Cohesive elements have been inserted between the interfaces of every neighbouring element along the fibre orientation for all 0° and 90° plies to predict the matrix cracking and splitting at predetermined crack spacing based on experimental observations. Good agreement is obtained between experimental and numerical crack density profiles for different 90° plies. In addition, different mechanisms of matrix cracking and growth processes were captured and splitting was also simulated in the bottom 0° ply by the numerical model.
    • Influencing the attachment of bacteria through laser surface engineering

      Gillett, Alice R.; Waugh, David G.; Lawrence, Jonathan; University of Chester (Laser Institute of America, 2015-10-31)
      Bacteria have evolved to become proficient at adapting to both extracellular and environmental conditions, which has made it possible for them to attach and subsequently form biofilms on varying surfaces. This has resulted in major health concerns and economic burden in both hospital and industrial environments. Surfaces which prevent this bacterial fouling through their physical structure represent a key area of research for the development of antibacterial surfaces for many different environments. Laser surface treatment provides a potential candidate for the production of anti-biofouling surfaces for wide ranging surface applications within healthcare and industrial disciplines. In the present study, a KrF 248 nm Excimer laser was utilized to surface pattern Polyethylene terephthalate (PET). The surface topography and roughness were determined with the use of a Micromeasure 2, 3D profiler. Escherichia coli (E. coli) growth was analysed at high shear flow using a CDC Biofilm reactor for 48 hours, scanning electron microscopy was used to determine morphology and total viable counts were made. Through this work it has been shown that the surface modification significantly influenced the distribution and morphology of the attached E. coli cells. What is more, it has been evidenced that the laser-modified PET has been shown to prevent E. coli cells from attaching themselves within the laser-induced micro-surface-features.
    • Modulating the wettability characteristics and bioactivity of polymeric materials using laser surface treatment

      Waugh, David G.; Lawrence, Jonathan; Shukla, Pratik; University of Chester (Laser Institute of America, 2015-10)
      It has been thoroughly demonstrated previously that lasers hold the ability to modulate surface properties of materials with the result being utilization of such lasers in both research and industry. What is more, these laser surface treatments have been shown to affect the adhesion characteristics and bio-functionality of those materials. This paper details the use of a Synrad CO2 laser marking system to surface treat nylon 6,6 and polytetrafluoroethylene (PTFE). The laser-modified surfaces were analyzed using 3D surface profilometry to ascertain an increase in surface roughness when compared to the as-received samples. The wettability characteristics were determined using the sessile drop method and showed variations in contact angle for both the nylon 6,6 and PTFE. For the PTFE it was shown that the laser surface treatment gave rise to a more hydrophobic surface with contact angles of up to 150° being achieved. For the nylon 6,6, it was observed that the contact angle was modulated approximately ±10° for different samples which could be attributed to a likely mixed state wetting regime. The effects of the laser surface treatment on osteoblast cell and stem cell growth is discussed showing an overall enhancement of biomimetic properties, especially for the nylon 6,6. This work investigates the potential governing parameters which drives the wettability/adhesion characteristics and bioactivity of the laser surface treated polymeric materials.
    • Modifications of surface properties of beta Ti by laser gas diffusion nitriding

      Ng, Chi-Ho; Lawrence, Jonathan; Waugh, David G.; Chan, Chi-Wai; Man, Hau-Chung; University of Chester (Laser Institute of America, 2015-10)
      β -type Ti-alloy is a promising biomedical implant material as it has a low Young’s modulus but is also known to have inferior surface hardness. Various surface treatments can be applied to enhance the surface hardness. Physical vapour deposition (PVD) and chemical vapour deposition (CVD) are two examples of this but these techniques have limitations such as poor interfacial adhesion and high distortion. Laser surface treatment is a relatively new surface modification method to enhance the surface hardness but its application is still not accepted by the industry. The major problem of this process involves surface melting which results in higher surface roughness after the laser surface treatment. This paper will report the results achieved by a 100 W CW fiber laser for laser surface treatment without the surface being melted. Laser processing parameters were carefully selected so that the surface could be treated without surface melting and thus the surface finish of the component could be maintained. The surface and microstructural characteristics of the treated samples were examined using X-ray diffractometry (XRD), optical microscopy (OM), 3-D surface profile & contact angle measurements and nano-indentation test.
    • An Analysis of Virtual Team Characteristics: A Model for Virtual Project Managers

      Cormican, Kathryn; Morley, Sandra; Folan, Paul; College of Engineering & Informatics, National University of Ireland, Galway. Ireland. College of Engineering, Mathematics and Physical Sciences, University of Exeter, Exeter, Devon UK United Kingdom. (Facultad de Economía y Negocios, Universidad Alberto Hurtado, 2015-04)
      An integrated model, created to guide project managers, is outlined for the implementation and management of virtual teams. This model is developed by means of an exploratory literature review and an empirical investigation of virtual team utilization in a multinational medical device manufacturer, which examines several factors critical to their success. A TOWS matrix is used to structure the results of the analysis and to identify future virtual team strategies for the organization. The study demonstrates that a structured approach is essential to ensure that the benefits resulting from virtual teamwork are maximized.
    • Laser surface treatment of polyamide and NiTi alloy and the effects on mesenchymal stem cell response

      Waugh, David G.; Lawrence, Jonathan; Shukla, Pratik; Chan, Chi-Wai; Hussain, Issam; Man, Hau-Chung; Smith, Graham C.; University of Chester ; University of Chester ; University of Chester ; Queen's University, Belfast ; University of Lincoln ; Hong Kong Polytechnic University ; University of Chester (2015-03-18)
      Mesenchymal stem cells (MSCs) are known to play important roles in development, post-natal growth, repair, and regeneration of mesenchymal tissues. What is more, surface treatments are widely reported to affect the biomimetic nature of materials. This paper will detail, discuss and compare laser surface treatment of polyamide (Polyamide 6,6), using a 60 W CO2 laser, and NiTi alloy, using a 100 W fiber laser, and the effects of these treatments on mesenchymal stem cell response. The surface morphology and composition of the polyamide and NiTi alloy were studied by scanning electron microscopy (SEM) and X-ray photoemission spectroscopy (XPS), respectively. MSC cell morphology cell counting and viability measurements were done by employing a haemocytometer and MTT colorimetric assay. The success of enhanced adhesion and spreading of the MSCs on each of the laser surface treated samples, when compared to as-received samples, is evidenced in this work.
    • Development of laser peening ceramics

      Shukla, Pratik; Lawrence, Jonathan; Waugh, David G.; University of Chester (2015-03)
    • Laser surface induced roughening of polymeric materials and the effects on Wettability characteristics

      Waugh, David G.; Lawrence, Jonathan; Shukla, Pratik; University of Chester (2015-01-15)
      It has been thoroughly demonstrated previously that lasers hold the ability to modulate surface properties of polymers with the result being utilization of such lasers in both research and industry. With increased applications of wettability techniques within industries there is greater need of predicting related characteristics, post laser processing, since such work evaluates the effectiveness of these surface treatments. This paper details the use of a Synrad CO2 laser marking system to surface roughen polymeric materials, namely: nylon 6,6; nylon 12, polytetrafluoroethylene (PTFE) and polyethylene (PE). These laser-modified surfaces have been analyzed using 3D surface profilometry to ascertain the surface roughness with the wettability characteristics obtained using a wettability goniometer. From the surface roughness results, for each of the samples, generic wettability characteristics arising from laser surface roughening is discussed.
    • Surface glazing of concrete using lasers for protection and decommissioning

      Lawrence, Jonathan; Waugh, David G.; Shukla, Pratik; University of Chester (2015-01)
    • Laser sealing of HDLPE film to PP substrate

      Shukla, Pratik; Lawrence, Jonathan; Waugh, David G.; University of Chester (2015-01)
    • Laser surface engineering of polymeric materials and the effects on wettability characteristics

      Waugh, David G.; Avdic, Dalila; Woodham, K. J.; Lawrence, Jonathan; University of Lincoln (Scrivener/John Wiley & Sons., 2014-12-23)
      Wettability characteristics are believed by many to be the driving force in applications relating to adhesion. So, gaining an in-depth understanding of the wettability characteristics of materials before and after surface treatments is crucial in developing materials with enhanced adhesion properties. This chapter details some of the main competing techniques to laser surface engineering followed by a review of current cutting edge laser surface engineering techniques which are used for wettability and adhesion modulation. A study is provided in detail for laser surface treatment (using IR and UV lasers) of polymeric materials. Sessile drop analysis was used to determine the wettability characteristics of each laser surface treated sample and as-received sample, revealing the presence of a mixed-state wetting regime on some samples. Although this outcome does not follow current and accepted wetting theory, through numerical analysis, generic equations to predict this mixed state wetting regime and the corresponding contact angle are discussed.
    • Laser surface engineering: Processes and applications

      Waugh, David G.; Lawrence, Jonathan; University of Chester (Woodhead Publishing, 2014-10-14)
      Lasers can alter the surface composition and properties of materials in a highly controllable way, which makes them efficient and cost-effective tools for surface engineering. This book provides an overview of the different techniques, the laser-material interactions and the advantages and disadvantages for different applications.
    • Laser surface structuring of ceramics, metals and polymers for biological applications: A review

      Shukla, Pratik; Waugh, David G.; Lawrence, Jonathan; University of Chester (Elsevier, 2014-10-14)
    • Laser melting of NiTi and its effects on in-vitro mesenchymal stem cell responses

      Waugh, David G.; Lawrence, Jonathan; Chan, Chi-Wai; Hussain, Issam; Man, Hau-Chung; University of Chester ; University of Chester ; University of Lincoln ; University of Lincoln ; Hong Kong Polytechnic University (Woodhead Publishing, 2014-10-14)