• High speed CO2 laser surface modification of iron/cobalt co-doped boroaluminosilicate glass

      Hodgson, Simon D.; Waugh, David G.; Gillett, Alice R.; Lawrence, Jonathan; University of Chester (IOP Publishing, 2016-06-10)
      A preliminary study into the impact of high speed laser processing on the surface of iron and cobalt co-doped glass substrates using a 60 W continuous wave (cw) CO2 laser. Two types of processing, termed fill-processing and line-processing, were trialled. In fill-processed samples the surface roughness of the glass was found to increase linearly with laser power from an Sa value of 20.8 nm–2.1 μm at a processing power of 54 W. With line processing, a more exponential-like increase was observed with a roughness of 4 μm at 54 W. The change in surface properties of the glass, such as gloss and wettability, have also been measured. The contact angle of water was found to increase after laser processing by up to 64°. The surface gloss was varied between 45 and 100 gloss units (GUs).
    • In vitro mesenchymal stem cell response to a CO2 laser modified polymeric material

      Waugh, David G.; Hussain, Issam; Lawrence, Jonathan; Smith, Graham C.; Toccaceli, Christina; University of Chester; University of Lincoln (Elsevier, 2016-05-16)
      With an ageing world population it is becoming significantly apparent that there is a need to produce implants and platforms to manipulate stem cell growth on a pharmaceutical scale. This is needed to meet the socio-economic demands of many countries worldwide. This paper details one of the first ever studies in to the manipulation of stem cell growth on CO2 laser surface treated nylon 6,6 highlighting its potential as an inexpensive platform to manipulate stem cell growth on a pharmaceutical scale. Through CO2 laser surface treatment discrete changes to the surfaces were made. That is, the surface roughness of the nylon 6,6 was increased by up to 4.3 µm, the contact angle was modulated by up to 5° and the surface oxygen content increased by up to 1 atom%. Following mesenchymal stem cell growth on the laser treated samples, it was identified that CO2 laser surface treatment gave rise to an enhanced response with an increase in viable cell count of up to 60,000 cells/ml when compared to the as-received sample. The effect of surface parameters modified by the CO2 laser surface treatment on the mesenchymal stem cell response is also discussed along with potential trends that could be identified to govern the mesenchymal stem cell response.
    • Laser surface induced roughening of polymeric materials and the effects on Wettability characteristics

      Waugh, David G.; Lawrence, Jonathan; Shukla, Pratik; University of Chester (2015-01-15)
      It has been thoroughly demonstrated previously that lasers hold the ability to modulate surface properties of polymers with the result being utilization of such lasers in both research and industry. With increased applications of wettability techniques within industries there is greater need of predicting related characteristics, post laser processing, since such work evaluates the effectiveness of these surface treatments. This paper details the use of a Synrad CO2 laser marking system to surface roughen polymeric materials, namely: nylon 6,6; nylon 12, polytetrafluoroethylene (PTFE) and polyethylene (PE). These laser-modified surfaces have been analyzed using 3D surface profilometry to ascertain the surface roughness with the wettability characteristics obtained using a wettability goniometer. From the surface roughness results, for each of the samples, generic wettability characteristics arising from laser surface roughening is discussed.
    • Laser surface treatment of polyamide and NiTi alloy and the effects on mesenchymal stem cell response

      Waugh, David G.; Lawrence, Jonathan; Shukla, Pratik; Chan, Chi-Wai; Hussain, Issam; Man, Hau-Chung; Smith, Graham C.; University of Chester ; University of Chester ; University of Chester ; Queen's University, Belfast ; University of Lincoln ; Hong Kong Polytechnic University ; University of Chester (2015-03-18)
      Mesenchymal stem cells (MSCs) are known to play important roles in development, post-natal growth, repair, and regeneration of mesenchymal tissues. What is more, surface treatments are widely reported to affect the biomimetic nature of materials. This paper will detail, discuss and compare laser surface treatment of polyamide (Polyamide 6,6), using a 60 W CO2 laser, and NiTi alloy, using a 100 W fiber laser, and the effects of these treatments on mesenchymal stem cell response. The surface morphology and composition of the polyamide and NiTi alloy were studied by scanning electron microscopy (SEM) and X-ray photoemission spectroscopy (XPS), respectively. MSC cell morphology cell counting and viability measurements were done by employing a haemocytometer and MTT colorimetric assay. The success of enhanced adhesion and spreading of the MSCs on each of the laser surface treated samples, when compared to as-received samples, is evidenced in this work.
    • Modulating the wettability characteristics and bioactivity of polymeric materials using laser surface treatment

      Waugh, David G.; Lawrence, Jonathan; Shukla, Pratik; University of Chester (Laser Institute of America, 2015-10)
      It has been thoroughly demonstrated previously that lasers hold the ability to modulate surface properties of materials with the result being utilization of such lasers in both research and industry. What is more, these laser surface treatments have been shown to affect the adhesion characteristics and bio-functionality of those materials. This paper details the use of a Synrad CO2 laser marking system to surface treat nylon 6,6 and polytetrafluoroethylene (PTFE). The laser-modified surfaces were analyzed using 3D surface profilometry to ascertain an increase in surface roughness when compared to the as-received samples. The wettability characteristics were determined using the sessile drop method and showed variations in contact angle for both the nylon 6,6 and PTFE. For the PTFE it was shown that the laser surface treatment gave rise to a more hydrophobic surface with contact angles of up to 150° being achieved. For the nylon 6,6, it was observed that the contact angle was modulated approximately ±10° for different samples which could be attributed to a likely mixed state wetting regime. The effects of the laser surface treatment on osteoblast cell and stem cell growth is discussed showing an overall enhancement of biomimetic properties, especially for the nylon 6,6. This work investigates the potential governing parameters which drives the wettability/adhesion characteristics and bioactivity of the laser surface treated polymeric materials.
    • Modulating the wettability characteristics and bioactivity of polymeric materials using laser surface treatment

      Waugh, David G.; Lawrence, Jonathan; Shukla, Pratik; University of Chester (AIP Publishing, 2016-03-31)
      It has been thoroughly demonstrated previously that lasers hold the ability to modulate surface properties of materials with the result being utilization of such lasers in both research and industry. What is more, these laser surface treatments have been shown to affect the adhesion characteristics and bio-functionality of those materials. This paper details the use of a Synrad CO2 laser marking system to surface treat nylon 6,6 and polytetrafluoroethylene (PTFE). The laser-modified surfaces were analyzed using 3D surface profilometry to ascertain an increase in surface roughness when compared to the as-received samples. The wettability characteristics were determined using the sessile drop method and showed variations in contact angle for both the nylon 6,6 and PTFE. For the PTFE it was shown that the laser surface treatment gave rise to a more hydrophobic surface with contact angles of up to 150° being achieved. For the nylon 6,6, it was observed that the contact angle was modulated approximately ±10° for different samples which could be attributed to a likely mixed state wetting regime. The effects of the laser surface treatment on osteoblast cell and stem cell growth is discussed showing an overall enhancement of biomimetic properties, especially for the nylon 6,6. This work investigates the potential governing parameters which drives the wettability/adhesion characteristics and bioactivity of the laser surface treated polymeric materials.