• Measurement of Interphase Forces based on Dual-modality ERT/DP Sensor in Horizontal Two-phase Flow Gas-water

      Fang, Lide; Wang, Peipei; Zeng, Qiaoqiao; Li, Mingming; Li, Xiaoting; Wang, Mi; Faraj, Yousef; Wang, Qiang; University of Chester; University of Leeds; Hebei University (China)
      In order to better understand the mechanisms of two-phase flow and the prevailing flow regimes in horizontal pipelines, the evaluation of interphase forces is paramount. This study develops a method to quantitatively estimate the interphase force in two-phase gas-water flow in horizontal pipeline. The electrical resistance tomography technology is used to measure the void fraction, while the differential pressure perpendicular to the horizontal pipe is measured in different flow patterns via a Differential Pressure sensor. The inner pipe diameter is 50 mm, the water flow range from 3.26 m3/h to 7.36 m3/h, the gas flowrate range from 1 to 60 l/min, which covered a range of flow patterns, the absolute pressure range from0.07 MPa to 0.12 MPa. The relationship between the differential pressure drop and interphase force is established, and the effects of these forces on the flow are analyzed. Experimental results indicate that the dual-modality measurement system was successfully provided a quantitative evaluation of inter-phase forces in two-phase horizontal gas-water flow.
    • Measurement of vertical oil-in-water two-phase flow using dual-modality ERT–EMF system

      Faraj, Yousef; Wang, Mi; Jia, Jiabin; Wang, Qiang; Xie, Cheng-gang; Oddie, Gary; Primrose, Ken; Qiu, Changhua; University of Leeds; Sate Key Lab. of O&G Reservoir Geology and Exploitation, Southwest Petroleum University, China; Schlumberger Gould Research, Cambridge; Industrial Tomography System plc, Manchester (Elsevier, 2015-08-21)
      Oil-in-water two-phase flows are often encountered in the upstream petroleum industry. The measurement of phase flow rates is of particular importance for managing oil production and water disposal and/or water reinjection. The complexity of oil-in-water flow structures creates a challenge to flow measurement. This paper proposes a new method of two-phase flow metering, which is based on the use of dual-modality system and multidimensional data fusion. The Electrical Resistance Tomography system (ERT) is used in combination with a commercial off-the-shelf Electromagnetic Flow meter (EMF) to measure the volumetric flow rate of each constituent phase. The water flow rate is determined from the EMF with an input of the mean oil-fraction measured by the ERT. The dispersed oil-phase flow rate is determined from the mean oil fraction and the mean oil velocity measured by the ERT cross-correlation velocity profiling. Experiments were carried out on a vertical upward oil-in-water pipe flow, 50 mm inner-diameter test section, at different total liquid flow rates covering the range of 8–16 m3/hr. The oil and water flow rate measurements obtained from the ERT and the EMF are compared to their respective references. The accuracy of these measurements is discussed and the capability of the measurement system is assessed.
    • Mechanism between Material Microstructures and Terahertz Dielectric Properties

      Yang, Bin; University of Chester (IEEE, 2019-10-21)
      Significant progress has been made in developing reliable Terahertz (THz) measurement spectroscopy to extract materials’ dielectric properties, however, systematic research on exploring intrinsic mechanism between microstructure of ceramics and THz dielectric properties such as loss, permittivity and dispersive characters has barely started. The paper focuses on one dielectric ceramic system (TiO2), its addition with Zn2SiO4 dielectrics and one hexa-ferromagnetic system to expatiate the association.
    • Mechanistic Studies of Compacted and Sintered Rock Salt

      Swanson, Claudia H.; Böhme, Susanne; Günster, Jens (John Wiley & Sons, Inc., 2016-09-26)
    • Methods for the Treatment of Cattle Manure—A Review

      Font Palma, Carolina (MDPI, 2019-05-15)
      Environmental concerns, caused by greenhouse gases released to the atmosphere and overrunning of nutrients and pathogens to water bodies, have led to reducing direct spread onto the land of cattle manure. In addition, this practice can be a source of water and air pollution and toxicity to life by the release of undesirable heavy metals. Looking at the current practices, it is evident that most farms separate solids for recycling purposes, store slurries in large lagoons or use anaerobic digestion to produce biogas. The review explores the potential for cattle manure as an energy source due to its relatively large calorific value (HHV of 8.7–18.7 MJ/kg dry basis). This property is beneficial for thermochemical conversion processes, such as gasification and pyrolysis. This study also reviews the potential for upgrading biogas for transportation and heating use. This review discusses current cattle manure management technologies—biological treatment and thermochemical conversion processes—and the diverse physical and chemical properties due to the differences in farm practices.
    • Micromachined cantilevers-on-membrane topology for broadband vibration energy harvesting

      Jia, Yu; Du, Sijun; Seshia, Ashwin A.; University of Cambridge; University of Chester (IOP Publishing, 2016-10-17)
      The overwhelming majority of microelectromechanical piezoelectric vibration energy harvesting topologies have been based on cantilevers, doubly-clamped beams or basic membranes. While these conventional designs offer simplicity, their broadband responses have been limited thus far. This paper investigates the feasibility of a new integrated cantilevers-on-membrane design that explores the optimisation of piezoelectric strain distribution and improvement of the broadband power output. While a classic membrane has the potential to offer a broader resonant peak than its cantilever counterpart, the inclusion of a centred proof mass compromises its otherwise high strain energy regions. The proposed topology addresses this issue by relocating the proof mass onto subsidiary cantilevers and combines the merits of both the membrane and the cantilever designs. Numerical simulations, constructed using fitted values based on finite element models, were used to investigate the broadband response of the proposed design in contrast to a classic plain membrane. Experimentally, when subjected to a band-limited white noise excitation, the new cantilevers-on-membrane harvester exhibited nearly two fold power output enhancement when compared to a classic plain membrane harvester of a comparable size.
    • A micromachined device describing over a hundred orders of parametric resonance

      Jia, Yu; Du, Sijun; Arroyo, Emmanuelle; Seshia, Ashwin A.; University of Cambridge; University of Chester (AIP Publishing, 2018-04-24)
      Parametric resonance in mechanical oscillators can onset from the periodic modulation of at least one of the system parameters, and the behaviour of the principal (1st order) parametric resonance has long been well established. However, the theoretically predicted higher orders of parametric resonance, in excess of the first few orders, have mostly been experimentally elusive due to the fast diminishing instability intervals. A recent paper experimentally reported up to 28 orders in a micromachined membrane oscillator. This paper reports the design and characterisation of a micromachined membrane oscillator with a segmented proof mass topology, in an attempt to amplify the inherent nonlinearities within the membrane layer. The resultant oscillator device exhibited up to over a hundred orders of parametric resonance, thus experimentally validating these ultra-high orders as well as overlapping instability transitions between these higher orders. This research introduces design possibilities for the transducer and dynamic communities, by exploiting the behaviour of these previously elusive higher order resonant regimes.
    • Micromachined Thick Mesh Filters for Millimeter-Wave and Terahertz Applications

      Wang, Yi; Yang, Bin; Tian, Yingtao; Donnan, Robert S.; Lancaster, Michael J.; University of Bolton (IEEE, 2014-03-01)
      This paper presents several freestanding bandpass mesh filters fabricated using an SU-8 based micromachining technique. The important geometric feature of the filters, which SU8 is able to increase, is the thickness of the cross-shaped micromachined slots. This is 5 times its width. This thickness offers an extra degree of control over the resonance characteristics. The large thickness not only strengthens the structures, but also enhances the resonance quality factor (Q-factor). A 0.3 mm thick, single layer, mesh filter resonant at 300 GHz has been designed, fabricated and its performance verified. The measured Q-factor is 16.3 and the insertion loss is 0.98 dB. Two multi-layer filter structures have also been demonstrated. The first one is a stacked structure of two single mesh filters producing a double thickness, which achieved a further increased Q-factor of 27. This is over six times higher than a thin mesh filter. The second multi-layer filter is an electromagnetically coupled structure forming a two-pole filter. The coupling characteristics are discussed based on experimental and simulation results. These thick mesh filters can potentially be used for sensing and material characterization at millimeter-wave and terahertz frequencies.
    • Microstructure and broadband dielectric properties of Zn2SiO4 ceramics with nano-sized TiO2 addition

      Weng, Zhangzhao; Song, Chunxiao; Xiong, Zhaoxian; Xue, Hao; Sun, Wenfeng; Zhang, Yan; Yang, Bin; Reece, Michael J.; Yan, Haixue; Xiamen University; Capital Normal University; University of Chester; Queen Mary, University of London; China Electronic Product Reliability and Environmental Testing Research Institute (Elsevier, 2019-04-06)
      Zn2SiO4 ceramics with nano-sized TiO2 addition (ZST) were synthesized by conventional solid state method. The association between the new composite’s microstructures and dielectric properties reveals that reduced pores, increased density and average grain sizes with increasing sintering temperatures, have contributed to the increased permittivities at kHz and microwave bands; the decrease of the permittivities at 1275 0C is due to the form of twin planes. At the terahertz band, the competition of generating oxygen vacancies and forming them into twin crystallographic shear planes dominates the change of permittivities: the crystallographic shear planes decrease the permittivity at the sintering temperature 12250C and 12500C, and the high-rate generation of oxygen vacancies at 1275 0C increases the permittivities. The ZST ceramics demonstrate stable permittivity and low dielectric losses (<10-3 from 10 kHz to microwave band; and < 10-2 at THz range); and the temperature coefficient of resonant frequency is optimized to close zero. These advanced dielectric properties and low sintering temperature (<13000C) provide the ZST ceramics great potential in designing microwave and THz devices.
    • Microwave and terahertz dielectric properties of MgTiO3–CaTiO3 ceramics

      Huang, Jinbao; Yang, Bin; Yu, Chuying; Zhang, Guang; Xue, Hao; Xiong, Zhaoxian; Viola, Giuseppe; Donnan, Robert S.; Yan, Haixue; Reece, Michael J.; et al. (Elsevier, 2015-10-05)
      The THz dielectric properties of MgTiO3–CaTiO3 ceramics are reported. The ceramics were prepared via a solid-state reaction route and the sintering conditions were optimized to obtain ceramics with high permittivity and low loss in the terahertz frequency domain. The amount of impurities (MgTi2O5) and grain size increased with increasing sintering temperature. The dielectric properties improved with increasing density, and the best terahertz dielectric performance was obtained at 1260 °C, with a permittivity of 17.73 and loss of 3.07×10−3. Ceramics sintered above 1260 °C showed a sharp increase in loss, which is ascribed to an increase in the impurity content.
    • Millimeter-Wave Free-Space Dielectric Characterization

      Liu, Xiaoming; Gan, Lu; Yang, Bin; Anhui Normal University; Wuhu CEPREI Information Industry Technology Research Institute; University of Chester (Elsevier, 2021-05-07)
      Millimeter wave technologies have widespread applications, for which dielectric permittivity is a fundamental parameter. The non-resonant free-space measurement techniques for dielectric permittivity using vector network analysis in the millimeter wave range are reviewed. An introductory look at the applications, significance, and properties of dielectric permittivity in the millimeter wave range is addressed first. The principal aspects of free-space millimeter wave measurement methods are then discussed, by assessing a variety of systems, theoretical models, extraction algorithms and calibration methods. In addition to conventional solid dielectric materials, the measurement of artificial metamaterials, liquid, and gaseous-phased samples are separately investigated. The pros of free-space material extraction methods are then compared with resonance and transmission line methods, and their future perspective is presented in the concluding part.
    • Mixed dimension silver nanowires for solution processed, flexible, transparent and conducting electrodes with improved optical and physical properties

      Kumar, D.; Ghosh, S.; Stoichkov, Vasil; Smith, Graham C.; Kettle, Jeff; University of Chester; Bangor University (IOP Publishing, 2017-03-20)
      In this work, we present an alternative method for the spray coating of silver nanowires contact electrodes by employing a mixture of short and long nanowires. Mixed silver nanowires are found to give improve optical properties with 2-5% higher transparency for the same sheet resistance of 25 Ωsq-1, when compared to silver nanowires prepared with a single geometry nanowire. The figure of merit (FoM) for the 25 Ωsq-1 sheet resistance electrode was found to be highest for the mixed composition AgNWs-M1 based electrodes. Furthermore, the average root mean square surface roughness (Rq) parameter by WLI measurement are found to be lower for the mixed composition silver nanowires electrodes (Rq= 3-4 nm) when compare to the individual parent fixed dimension type silver nanowire electrodes (Rq = 6-8 nm).
    • Mixed-type functional differential equations: A numerical approach

      Ford, Neville J.; Lumb, Patricia M.; University of Chester (Elsevier, 2007-10-29)
      This preprint discusses mixed-type functional equations.
    • Mixed-type functional differential equations: A numerical approach (extended version)

      Ford, Neville J.; Lumb, Patricia M.; University of Chester (University of Chester, 2007)
    • Mobile technology-enhanced asset maintenance in an SME

      Bankosz, Grzegorz S.; Kerins, John; University of Chester (Emerald, 2014-05-06)
      This article discusses the development of a prototype system to demonstrate the potential benefits of deploying mobile technology to enhance asset maintenance processes in a small food manufacturing plant.
    • Model-directed engineering of “difficult-to-express” monoclonal antibody production by Chinese hamster ovary cells

      Pybus, Leon P.; Dean, Greg; West, Nathan R.; Smith, Andrew; Daramola, Olalekan; Field, Ray; Wilkinson, Stephen J.; James, David C.; University of Sheffield ; BioPharmaceutical Development ; University of Sheffield ; BioPharmaceutical Development ; BioPharmaceutical Development ; BioPharmaceutical Development ; University of Sheffield ; University of Sheffield; ChELSI Institute; Department of Chemical and Biological Engineering; University of Sheffield; Mappin Street Sheffield S1 3JD UK; et al. (Wiley, 2013-11-14)
      Despite improvements in volumetric titer for monoclonal antibody (MAb) production processes using Chinese hamster ovary (CHO) cells, some “difficult-to-express” (DTE) MAbs inexplicably reach much lower process titers.
    • Modelling impact damage in composite laminates: A simulation of intra- and inter-laminar cracking

      Pinna, Christophe; Soutis, Constantinos; Shi, Yu; University of Chester; University of Sheffield; University of Manchester (Elsevier, 2014-04-12)
      In this work, stress- and fracture mechanics-based criteria are developed to predict initiation and evolution, respectively, of intra- and inter-laminar cracking developed in composite laminates subjected to a relatively low energy impact (⩽15 J) with consideration of nonlinear shear behaviour. The damage model was implemented in the finite element (FE) code (Abaqus/Explicit) through a user-defined material subroutine (VUMAT). Delamination (or inter-laminar cracking) was modelled using interface cohesive elements while splitting and transverse matrix cracks (intralaminar cracking) that appeared within individual plies were also simulated by inserting cohesive elements along the fibre direction (at a crack spacing determined from experiments for computing efficiency). A good agreement is obtained when the numerically predicted results are compared to both experimentally obtained curves of impact force and absorbed energy versus time and X-ray radiography damage images, provided the interface element stiffness is carefully selected. This gives confidence to selected fracture criteria and assists to identify material fracture parameters that influence damage resistance of modern composite material systems.
    • Modelling low velocity impact induced damage in composite laminates

      Shi, Yu; Soutis, Constantinos; University of Chester; University of Manchester (SpringerOpen, 2017-07-26)
      The paper presents recent progress on modelling low velocity impact induced damage in fibre reinforced composite laminates. It is important to understand the mechanisms of barely visible impact damage (BVID) and how it affects structural performance. To reduce labour intensive testing, the development of finite element (FE) techniques for simulating impact damage becomes essential and recent effort by the composites research community is reviewed in this work. The FE predicted damage initiation and propagation can be validated by Non Destructive Techniques (NDT) that gives confidence to the developed numerical damage models. A reliable damage simulation can assist the design process to optimise laminate configurations, reduce weight and improve performance of components and structures used in aircraft construction.
    • Modelling low velocity impact induced damage in composite laminates

      Shi, Yu; Soutis, Constantinos; University of Chester; University of Manchester (Springer, 2017-07-26)
      The paper presents recent progress on modelling low velocity impact induced damage in fibre reinforced composite laminates. It is important to understand the mechanisms of barely visible impact damage (BVID) and how it affects structural performance. To reduce labour intensive testing, the development of finite element (FE) techniques for simulating impact damage becomes essential and recent effort by the composites research community is reviewed in this work. The FE predicted damage initiation and propagation can be validated by Non Destructive Techniques (NDT) that gives confidence to the developed numerical damage models. A reliable damage simulation can assist the design process to optimise laminate configurations, reduce weight and improve performance of components and structures used in aircraft construction.
    • Modelling the effects of glucagon during glucose tolerance testing

      Kelly, Ross A; Fitches, Molly J; Webb, Steven D; Pop, Serban R; Chidlow, Stewart J; Liverpool John Moores University; University of Dundee; University of Chester
      Background Glucose tolerance testing is a tool used to estimate glucose effectiveness and insulin sensitivity in diabetic patients. The importance of such tests has prompted the development and utilisation of mathematical models that describe glucose kinetics as a function of insulin activity. The hormone glucagon, also plays a fundamental role in systemic plasma glucose regulation and is secreted reciprocally to insulin, stimulating catabolic glucose utilisation. However, regulation of glucagon secretion by α-cells is impaired in type-1 and type-2 diabetes through pancreatic islet dysfunction. Despite this, inclusion of glucagon activity when modelling the glucose kinetics during glucose tolerance testing is often overlooked. This study presents two mathematical models of a glucose tolerance test that incorporate glucose-insulin-glucagon dynamics. The first model describes a non-linear relationship between glucagon and glucose, whereas the second model assumes a linear relationship. Results Both models are validated against insulin-modified and glucose infusion intravenous glucose tolerance test (IVGTT) data, as well as insulin infusion data, and are capable of estimating patient glucose effectiveness (sG) and insulin sensitivity (sI). Inclusion of glucagon dynamics proves to provide a more detailed representation of the metabolic portrait, enabling estimation of two new diagnostic parameters: glucagon effectiveness (sE) and glucagon sensitivity (δ). Conclusions The models are used to investigate how different degrees of patient glucagon sensitivity and effectiveness affect the concentration of blood glucose and plasma glucagon during IVGTT and insulin infusion tests, providing a platform from which the role of glucagon dynamics during a glucose tolerance test may be investigated and predicted.